View S-AU82AL_4110882.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

S-AU82AL
TOSHIBA RF POWER AMPLIFIER MODULE
S-AU82AL
FM RF POWER AMPLIFIER MODULE FOR 60-W COMMERCIAL UHF RADIO APPLICATIONS
Power Gain: 30.7 dB (Min.) Total Efficiency: 40% (Min.) ABSOLUTE MAXIMUM RATINGS (Tc = 25C, IT < 15 A, ZG = ZL = 50)
CHARACTERISTICS Maximum Current Power Supply Voltage Control Voltage Instantaneous Output Power Input Power Operating Case Temperature Storage Temperature SYMBOL IT VDD VGG Pomax Pi Tc (opr) Tstg VGG = 0 V (GND), RF: none 10.5 VDD 16.5 V, Pi = 50 mW VGG 5.5 V, Pi = 50 mW, 10.5 VDD 16.5V, within 2 seconds 10.5 VDD 16.5 V, VGG 5.5 V 10.5 VDD 16.5 V, VGG 5.5 V, Pi = 50 mW (Note 2) TEST CONDITION RATING 15 16.5 5.5 80 100 -30 to 100 -40 to 110 UNIT A V V W mW C C
Note 1: The maximum ratings are the limits that must not be exceeded even for an instant, under worst possible conditions. Exceeding the ratings may cause device damage, ignition, or deterioration. Therefore, when designing the circuitry, derating factors should be applied so that the absolute maximum ratings are not exceeded. Note 2: The output power rating satisfies the range shown in Figures 1 and 2 according to the operating case temperature. Ensure that the device should be operated within the specified operating range. The figures below indicate the output power obtained 2 seconds after Po is generated.
Pomax-Tc 70 60 50 40 30 20
PDmax-Tc 180 160 140 120 PDmax(W) 100 80 60 40
Pomax(W)
10 0 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 Tc ()
20
Power dissipation (PD) PD = (VDD x IDD) - Po + Pi
0 10 20 30 40 Tc() 50 60 70 80 90 100
0 -30 -20 -10
Figure 1 Pomax-Tc
Figure 2 PDmax-Tc
*When the device is used at Tc =100C, the output power rating is 60 W as shown in Figure 1. When the power dissipation at Tc = 100C exceeds the rating shown in Figure 2, the output derating is required to limit the dissipation within the specified range. Note 3: The case temperature is monitored using the screw terminal blocks on the input side that are used for the module implementation. Note 4: To protect a device from being permanently damaged, the power-on sequence must be as follows (, while the reversed order should be applied when turning off): 1. VDD, 2. Pi, 3. VGG
1
2007-06-21
S-AU82AL
PACKAGE OUTLINE
Unit: mm

RF Input RF Output JEDEC JEITA TOSHIBA Weight: 35 g
VGG VDD GROUND(Flange) -- -- 5-53P
ELECTRICAL CHARACTERISTICS (Tc = 25C, ZG = 50)
CHARACTERISTICS Frequency Range Output Power Power Gain Total Efficiency Input VSWR Second Harmonic Third Harmonic SYMBOL frange Po Gp T VSWRin 2nd HRM 3rd HRM 10.5 V VDD 16.5 V, 0 V VGG VGGajs (VGG = VGGajs @ Po = 60 W) Ruggedness -- Pi = 50 mW Po = 60 W (Adjusted via VGG @ ZL = 50) VSWR LOAD 20: 1 ALL PHASE (@ 2 s) 10.5 V VDD 16.5 V, 0 V VGG VGGajs Stability -- (VGG = VGGajs @ Po = 60 W) Pi = 50 mW Po 60 W (Adjusted via VGG @ ZL = 50) VSWR LOAD 3: 1 ALL PHASE No spurious output of -60 dB or greater -- No Damage -- VDD = 12.5 V VGG = 5 V Pi = 50 mW ZL = 50 TEST CONDITION -- MIN 400 60 30.7 40 -- -- -- TYP. -- -- -- -- -- -- -- MAX 470 -- -- -- 3.0 -30 -30 UNIT MHz W dB % -- dB dB
Note 5:The output power is intended to follow the rating provided in Figure 1 in Note 2. Note 6: Stability Measurements are performed under the conditions where VSWR is at 3:1 through all phases over the whole frequency range, and they are guaranteed only under those conditions. Even though it is guaranteed to be stable where VSWR is at 3:1, the VSWR load over the operating frequency should be designed to be 50 .At the same time, ensure that the VSWR load does not deviate much from 50 even for a moment, nor deviate even a little from 50 continually. The S-AU82AL is not intended for such operations, and proper operation under such conditions is not guaranteed due to the possibilities of heat generation in the module and its applications.
2
2007-06-21
S-AU82AL
HANDLING PRECAUTIONS
Since this product has a protective cap, care should be taken to avoid applying an excessive impact and allowing foreign objects to get inside when handling this product. Also, please do not remove a cap. If the cap is removed, the foreign object inside the module or the applied impact may lead IC failure, causing smoke or ignition. Since this product is structurally susceptible to static electricity, protections against the static electricity should be applied to objects that may come in direct contact with devices, such as worktables, equipment, operators and solder irons. This product is not designed nor intended to perform a continuous transmission for applications like a base station. Please do not use this product for such applications, for the reliability cannot be guaranteed. This product is intended to be used for a single operation (single-device operation). A proper operation is not guaranteed for a parallel operation. A parallel operation should be performed in accordance with your own good judgment. Mounting method The flatness of a heat sink must not exceed 50 m. If the flatness exceeds 50 m, the device may experience an unexpected stress that may lead to module breakdown due to damage or ignition in the substrate inside a module and other module parts. Please apply thermal compound between a module and a heat sink to improve the adhesive property. Use a 4-mm diameter screw with the clamping screw torque of 1.2 to 1.5 Nm. Please solder the module leads after the screw is clamped.
3
2007-06-21
S-AU82AL
EQUIVALENT CIRCUIT
Pi ZG = 50
Po ZL = 50
VGG
VDD
GROUND Flange
TEST FIXTURE
C1 Pi
C1 Po C2
C2
L
L
C1: 15000 pF C2: 10 F L: 0.8-mm enamel wire, 8T, 5ID
VGG
VDD
4
2007-06-21
S-AU82AL
MARKING TOSHIBA
L
Product Number (without A) This dot indicates that the actual product name is "S-AU82AL." Alphanumeric characters: Date of manufacture Dot: Indicates that this product is manufactured by "TOSHIBA COMPONENTS."
Explanation of Lot No.
Month of manufacture: January to December are denoted by letters A to L respectively. Year of manufacture: Last decimal digit of the year of manufacture
RESTRICTIONS ON PRODUCT USE
* The information contained herein is subject to change without notice.
20070701-EN
* TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the "Handling Guide for Semiconductor Devices," or "TOSHIBA Semiconductor Reliability Handbook" etc. * The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ("Unintended Usage"). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer's own risk. * The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. * The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. * Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations.
5
2007-06-21

▲Up To Search▲

Price & Availability of S-AU82AL

	To Download S-AU82AL Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .